What does “99% HPLC purity” actually mean on a peptide COA?
“99% purity” on a peptide certificate is usually the main peak’s share of the total UV peak area on one HPLC run. It does not measure water or counter-ions, it does not confirm identity, and it shifts with the method. Here is how to read it properly.
A certificate of analysis that says “99% purity” is one of the most quoted numbers in the peptide world, and one of the most misread. It sounds like a grade on the whole vial. It is usually something narrower: a ratio of peak areas on one chromatogram, run one way, on one day.
That does not make the number useless. It makes it a specific answer to a specific question. This guide walks through what that question is, what the number leaves out, and how to read it the way a lab technician would.
Where the percentage comes from
Most peptide purity figures come from reversed-phase high-performance liquid chromatography (HPLC). A small amount of the sample is dissolved and pushed through a packed column. Different molecules leave the column at different times, and a UV detector draws a line that rises into a peak each time something it can see passes by.
Bachem, a large Swiss peptide manufacturer, describes the standard method in its quality-control guide: purity “is typically assessed by UV detection at 210–220 nm, where the area of the main peak in relation to the total area of all peaks reflects the peptide purity.”
Put plainly, a technician adds up the area under every peak the software integrated, then works out what share of that total belongs to the biggest peak. If the main peak is 99 parts of 100, the certificate says 99%.
NovoPro, a custom peptide synthesis company, phrases it the same way in its customer FAQ: HPLC purity “corresponds to the percentage of requested peptide in relation to the total amount of material absorbing at 220 nm i.e. the desired product, peptidic by-products and other impurities.”
The key words are “material absorbing.” The percentage is a share of what the detector saw, not a share of what is in the vial.
What the 99% does not include
Freeze-dried peptide powder is not only peptide. Bachem’s own care-and-handling guide puts the gap in one sentence: “While peptides for research use are typically > 95% pure by HPLC, the peptide content of the solid may range from 70 to 90% as peptides contain counter ions (e.g. acetate, trifluoroacetate) and residual moisture.”
So there are two different numbers on a good certificate, and they answer two different questions:
- —HPLC purity asks: of the peaks the detector saw, how much was the main one?
- —Net peptide content asks: of the powder on the balance, how much was peptide at all?
Water and counter-ions (the salt partners left from purification) add weight but do not show up as peaks in the purity calculation. Bachem notes that “NPC and purity are not equivalent, because the former includes peptidic contaminants,” and NovoPro adds that “a relatively low peptide content can be expected when a peptide contains a large proportion of basic amino acids, especially arginines.” A very clean peptide can still be a smaller share of the powder than the purity figure suggests. That is chemistry, not a defect.
A separate guide on net content versus purity will go deeper. For this page, the point is simple: a high purity number is not a statement about how much material is in the vial.
What the 99% does not prove about identity
The main peak is the main peak. HPLC on its own does not say what molecule it is.
Bachem’s guide lists identity as its own question (“Is it the desired product?”) and treats it separately from purity. For peptides, “the molecular weight is determined by mass spectrometry.” A chromatogram can show a tall, clean peak for the wrong sequence, a truncated version, or a related compound. The percentage would still read beautifully.
That is why a purity figure without a mass spectrum on the same lot is half a record. Our guide on what a COA actually proves covers how those two tests fit together.
Why two labs can report different numbers for the same batch
A reader on TalkPeptides asked the question many people eventually reach: “What I am after is why two laboratories report different purity for the same batch, and which number to believe.”
A reply in the same thread gave the practical answer: variation “comes from real methodological differences, not sloppiness: which reference standard was used and how it was itself calibrated, the gradient and column, the detection wavelength, and where the integration baseline was drawn.” The same commenter added that “a percentage point or two between competent labs is expected,” and that a large gap usually means one report is not about the batch in your hand.
A few of those levers are worth knowing by name:
- —Wavelength. Most methods read near 214 or 220 nm. Impurities that absorb weakly at that wavelength count for less in the total.
- —Column and gradient. A gentler gradient can separate two molecules that a fast run lumps into one peak, which lowers the reported purity of the same powder.
- —Integration. Where the baseline is drawn, and which tiny peaks are counted, moves the total area.
So “99%” is really “99% under this method.” A careful certificate tells you the method. A careless one just gives the number.
How to read the purity line on a COA
Here is a short checklist to run on any certificate:
- —Is there a chromatogram, or only a number? The IPEC Federation’s 2024 Certificate of Analysis Guide recommends “reporting of actual data and observations” rather than non-specific “passes” or “conforms” statements. A trace you can look at is stronger than a bare percentage.
- —Is the method named? IPEC lists a “reference to the test method” among the specification items a certificate should carry. Column, wavelength or a method code tells you what the number means.
- —Does one peak clearly dominate? A main peak with small, separated neighbours is what a 99% result should look like. A shoulder on the main peak, or a messy baseline, is worth a question.
- —Is there a mass spectrum for the same lot? Purity without identity is the most common gap.
- —Does the lot number match your vial? A perfect result about another batch is not about yours. Our guide to parcel paperwork that agrees with itself shows how to match lot, name and quantity.
If you want a full walk-through of every section on a certificate, see how to read a peptide COA. For record-keeping habits that separate a careful supplier from a careless one, see how to tell a real supplier from a fake one.
Frequently asked questions
Does 99% HPLC purity mean 99% of the powder is peptide?
No. It is usually the main peak’s share of the total peak area the UV detector saw. Water and counter-ions add weight to the powder without appearing in that calculation, so the peptide share of the powder is typically lower.
Is 98% worse than 99%?
Not necessarily. Two labs can report a point or two apart on the same batch because of column, wavelength, gradient and integration choices. The method and the chromatogram matter more than a one-point difference.
Can a 99% result be the wrong molecule?
Yes. HPLC measures how dominant the main peak is, not what it is. Identity is confirmed by mass spectrometry, which should be reported for the same lot.
What should a purity line on a COA include?
A number, the method it was measured by, an acceptance criterion, and ideally the chromatogram itself, all tied to the lot number printed on the vial.
Sources
Neutral background on the methods themselves, written by no seller: High-Performance Liquid Chromatography (Chemistry LibreTexts, a university-hosted open textbook), Liquid chromatography–mass spectrometry (Wikipedia), and Certificate of analysis (Wikipedia).
- —Bachem, *Quality Control of Amino Acids & Peptides: A Guide*, opened 10 November 2026: bachem.com quality-control guide
- —Bachem, *Care and Handling of Peptides*, opened 10 November 2026: bachem.com care and handling
- —NovoPro Labs, *Frequently Asked Questions of Peptides*, opened 10 November 2026: novoprolabs.com peptide FAQ
- —IPEC Federation, *Certificate of Analysis Guide for Pharmaceutical Excipients*, 2024 edition, opened 10 November 2026: IPEC 2024 COA guide (PDF)
- —TalkPeptides, “Understanding peptide purity percentages,” public thread, opened 10 November 2026: talkpeptides.net thread
Ask Kobi
Got a peptide question? Kobi runs a free Canadian peptide info line: Message Kobi on WhatsApp.
Send him the chromatogram and the purity line from a certificate if you want a second pair of eyes on what the number does and does not say.
Research peptides. Minus the hype.
Key takeaways
- HPLC purity is usually the main peak’s share of the total UV peak area, not the share of the powder that is peptide.
- Water and counter-ions add weight without appearing in the purity figure; Bachem says research peptides above 95% HPLC purity may be 70 to 90% peptide by content.
- Purity does not confirm identity: a mass spectrum on the same lot answers whether the main peak is the right molecule.
- A point or two between labs is normal because column, wavelength, gradient and integration differ; the method and chromatogram matter more than the number alone.
We source from distributors whose batches are third-party tested for HPLC purity and measured content. Certificates of Analysis (COAs) are for members only.